Recent years have witnessed to a massive increase in demand for LCD and plasma TVs that seem increasingly thinner, lighter and more powerful. There are several good reasons pirchasing for a new HDTV, such as high-definition viewing more than obvious, affordable and energy savings. These new designs make fine Plasma and LCD HDTVs ideal for wall mounting. Not only the wall mounting your TV free up valuable space in your room, but can add an element of aesthetic appeal to the configuration your home theater. Here are some suggestions on how to mount your screen.
Before starting the mounting hardware you need to decide on the best position to mount your TV. Careful planning is necessary for an HDTV wall is much more a permanent solution and will be integrated into the design of your home. You should consider the placement of your furniture, the overall theme of your room, the potential of viewing angles and better positioning of audio. Once you think that you have chosen a proper position you should get a piece of cardboard or wrapping paper and cut the size of the TV screen. You should then approach putting tape on the sheet of cardboard or paper to the wall where the screen will be placed and then mark it with a pencil.
Remove the support from the back of the screen if it is still connected and then put the TV is expensive. Next you need to locate the four mounting on the back of the TV and remove the screws. Once this is done, you must remove the mounting brackets or mounting plate wall mount packaging. To attach the mounting brackets, need to align them vertically and parallel to each other, using the mounting holes on the back of the television. Make sure they are in perfect alignment and then Bolt's arms using the supplied screws and washers, which should have come with the wall mount. If you are using a mounting plate, then it is very easy to align the holes with the mounting holes on television.
Locate the wall studs that are closer to the screen position required using a screw finder prisoner and mark them out with a sharp pencil. Now you need to remove the wall mount packaging. Align the wall mount to the studs in the center position marked that you determined earlier. No matter if it is not perfectly centered as the wall mount can be adjusted horizontally at a later time.
Using a spirit level, the assembly line on the wall and then mark the position of the screws go. Next holes for the stud that are approximately 1 "deep. The size of the drill you need to use is determined by the size of the screws provided with wall bracket. Bolt the wall mount to the wall using supplied screws and washers, however, do not tighten the screws completely. Adjust the position of the wall mount horizontally until you are happy with the alignment. When you are satisfied with the positioning of the screen, you are free to tighten the screws the rest of the path.
Attatching the screen to mount on the wall has two people. Just lift the TV and connect it to the wall mount. At this point, you will still be able to adjust the horizontal positioning to position the screen perfectly. Once the desired position has been acquired you need to fully tighten the mounting arms or plate of the wall mount.
About the Author:
Dave Matthews is writing on behalf of Value TV Brackets, a supplier of quality flat screen
LCD TV brackets
.
Article Source: ArticlesBase.com – How to Wall Mount a Flat Screen TV
How to get a FREE MACBOOK, IPOD TOUCH or MONEY(NO CREDIT CARD NEEDED)
|
|
NEW BLACK 17 FLIP DOWN OVERHEAD ROOF MOUNT HIGH RESOLUTION LCD CAR MONITOR SCREEN $199.00 When it comes to TV Screen size, it’s no doubt bigger is ALWAYS better. You are looking at a Brand new 17″ roof mount LCD monitor. This super thin super light model featuring a HUGE bright, high resolution (1440 X 900) digital TFT LCD panel, Product comes with all wiring, mounting hardwares and remote control…. |
|
|
InstallerNet Big Screen Wall Mount InstallCard $399.99 With this InstallCard professional installers will come to your home to unpack, connect and mount your Big Screen video device (panels with 30 inch diagonal or larger) on a wall. Connections will include existing A/V source and existing A/V components co-located in the same room up to 15 cable-feet apart. Installation includes limited wire fishing, for concealment only, of A/V source and connectio… |
|
|
AC Power Adaptor for Nintendo Wii Console $0.99 You won’t regret your purchase!!!… |
